CoraZ7s custom bit file, usbhid: USB HID core driver

[rick chaney]

When a custom bit files is used the petalinux fails.

I am assuming the Petalinux build is expecting a PL XADC support?

Is the a way to exclude this from the Petalinux build?

 

Thanks Rick

Linux version 4.9.0-xilinx-v2017.4 (setup@usrd23715) (gcc version 6.2.1 20161016 (Linaro GCC 6.2-2016.11) ) #1 SMP PREEMPT Thu Oct 11 15:36:08 EDT 2018

........

usbcore: registered new interface driver usbhid

usbhid: USB HID core driver

Unhandled fault: imprecise external abort (0x406) at 0x000bc834

pgd = c0004000

[000bc834] *pgd=00000000

Internal error: Oops - BUG: 406 [#1] PREEMPT SMP ARM

Modules linked in:

CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.9.0-xilinx-v2017.4 #1

Hardware name: Xilinx Zynq Platform

task: de44b640 task.stack: de44c000

PC is at xadc_axi_read_adc_reg+0x14/0x20

LR is at xadc_probe+0x430/0x6bc

.......

[<c04e6eac>] (xadc_axi_read_adc_reg) from [<c04e8108>] (xadc_probe+0x430/0x6bc)

[<c04e8108>] (xadc_probe) from [<c039dd38>] (platform_drv_probe+0x50/0x9c)

[<c039dd38>] (platform_drv_probe) from [<c039c7d4>] (driver_probe_device+0x1b0/0x274)

[<c039c7d4>] (driver_probe_device) from [<c039c914>] (__driver_attach+0x7c/0xa8)

[<c039c914>] (__driver_attach) from [<c039b044>] (bus_for_each_dev+0x7c/0x8c)

[<c039b044>] (bus_for_each_dev) from [<c039bf34>] (bus_add_driver+0x16c/0x1dc)

[<c039bf34>] (bus_add_driver) from [<c039d030>] (driver_register+0xa0/0xe0)

[<c039d030>] (driver_register) from [<c0101858>] (do_one_initcall+0x100/0x120)

[<c0101858>] (do_one_initcall) from [<c0900da4>] (kernel_init_freeable+0x190/0x1d8)

[<c0900da4>] (kernel_init_freeable) from [<c0603a98>] (kernel_init+0x8/0x10c)

[<c0603a98>] (kernel_init) from [<c0106d18>] (ret_from_fork+0x14/0x3c)

 

 

 

[jpeyron]

Hi @rick chaney,

I moved your thread to a sub-section where more experienced embedded linux engineers look. Also , here is a thread that might be helpful. 

cheers,

Jon

[vicentiu]

Hello,

How did you introduce this custom bit file into Petalinux?

What kind of changes did you make to the FPGA IP (contained in the bit file) compared to the original bit file? You may need to modify the device tree also to properly describe the resources available in your custom bit file.

Is it the kernel booting that is giving you the Unhandled Fault error?

Are you working with our reference Petalinux project for the Cora Z7?

Vicentiu

[rick chaney]

I have developed a bit file for a standalone operation for the CoraZ7s.

Then attempted to the use the Digilent https://github.com/Digilent/Petalinux-Cora-Z7-07S/blob/master/README.md

I first ran the Petalinux with the supplied system_wrapper.bit. Work fine.

Then replaced the bit file in the /images/linux directory with my own bit file. Then ran the "petalinux-package --boot --force --fsbl images/linux/zynq_fsbl.elf --fpga images/linux/system_wrapper.bit --u-boot" command. And booted from SD card.

The error indications suggests there are some IP definitions required for this to run. From the error indicated above it appears there is a XADC ip core included in the Digilent bit file.

So I am left with 2 choices;

1. re-create my bit design -with the Digilent defined XADC interface.

2. modify the Petalinux build to remove the XADC(USB HID ) driver.

 

Any suggestions?

Thanks Rick

[vicentiu]

Either option is probably about the same effort... depending on which one you are more familiar with: Vivado or Petalinux.

I recommend the one you're most familiar with.

[rick chaney]

Where can I get the Vivado project files that will with the CoraZ7s Petalinux ?

 

[rick chaney]

Which PetaLinux config file do I modify to exclude the XADC interface?

[vicentiu]

7 minutes ago, rick chaney said:

Where can I get the Vivado project files that will with the CoraZ7s Petalinux ?

 

Depending on which Cora board you have, it one of the following:

https://github.com/Digilent/Cora-Z7-07S-base-linux

https://github.com/Digilent/Cora-Z7-10-base-linux

[vicentiu]

4 minutes ago, rick chaney said:

Which PetaLinux config file do I modify to exclude the XADC interface?

It's in a device tree file. Look for "xadc" in *.dts and *.dtsi files in the project.

[rick chaney]

https://github.com/Digilent/Cora-Z7-07S-base-linux

zip file doesnt contain anyVivado Project files?

The Readme file is blank?

 

[vicentiu]

On 10/12/2018 at 8:48 PM, rick chaney said:

zip file doesnt contain anyVivado Project files?

The Readme file is blank?

You need to run the script proj/create_project.tcl from within Vivado to create the project files.

We've noted to add a readme file to this repo.

thanks