Search the Community

Showing results for tags 'xadc header'.



More search options

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • News
    • New Users Introduction
    • Announcements
  • Digilent Technical Forums
    • FPGA
    • Digilent Microcontroller Boards
    • Non-Digilent Microcontrollers
    • Add-on Boards
    • Scopes & Instruments
    • LabVIEW
    • FRC
    • Other
  • General Discussion
    • Project Vault
    • Learn
    • Suggestions & Feedback
    • Buy, Sell, Trade
    • Sales Questions
    • Off Topic
    • Educators
    • Technical Based Off-Topic Discussions

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


AIM


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


Location


Interests

Found 3 results

  1. Hello, I am kind of new to FPGAs and I am trying to use the XADC in order to monitor the temperature sensor: I am using Vivado 2018.2, Nexys video as a board. I used the IP catalog in order to set up the XADC as following: DRP, Single channel, continuous, disable all alarms, disable reset_in, channel to monitor: temperature I wrote a top level module which reads the bits 4 up to 7 from do_out and light up LEDs accordingly: //part of the top module: module top( input CLK100MHZ, input vp_in, input vn_in, input [1:0] sw, output reg [11:0] LED ); wire enable; wire ready; wire [15:0] data; reg [6:0] Address_in; xadc_wiz_0 XLXI_7 (.daddr_in(Address_in), //addresses can be found in the artix 7 XADC user guide DRP register space .dclk_in(CLK100MHZ), .den_in(enable), .di_in(0), .dwe_in(0), .busy_out(), .vn_in(vn_in), .vp_in(vp_in), .alarm_out(), .do_out(data), .eoc_out(enable), .channel_out(), .drdy_out(ready)); always @( posedge(CLK100MHZ)) begin if(ready == 1'b1) begin case (data[7:4]) 4'b0001: LED <= 12'b000000000001; 4'b0: LED <= 12'b0; 4'b1000: LED<=12'b000000000010; default: LED <= 12'b1; endcase end end ///// I have one problem though, as I come to set the address of the ddr_in as done in a documentation found here which has LEDs displaying potential differences monitored by XADC, I do not understand what 8 bit address I should assign for the DRP to monitor the Temperature Channel ! "Address_in <= 8'h ????" My goal: I need the LEds to display something for the sake of demonstration that I am able to read values out of the do_out. Thank you for your help.
  2. Is there a way to just input a voltage and read it through the terminal using the XADC Header on the Zynq 7000 Zedboard? If so can this be done using the VP VN pins?
  3. Hi, I'm trying to measure an external Voltage connected to the AUX0 pin of the XADC header using Zedboard .While measuring the output I find that the voltage is shows higher value by factor 3 or even 4 of the input differential voltage applied. I'm unable to figure out why this is happening. C code file is attached also. I have followed the following thread while performing my project too https://forum.digilentinc.com/topic/4311-zedboard-zynq-7000-xadc-header/?page=0#comment-16891 I have connected AUXP0 to 0.2 V and AUXN0 to GND . Could someone help on this?? helloworld.c