Search the Community

Showing results for tags 'wi-fire'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


  • News
    • New Users Introduction
    • Announcements
  • Digilent Technical Forums
    • FPGA
    • Digilent Microcontroller Boards
    • Non-Digilent Microcontrollers
    • Add-on Boards
    • Test and Measurement
    • LabVIEW
    • FRC
    • Other
  • General Discussion
    • Project Vault
    • Learn
    • Suggestions & Feedback
    • Buy, Sell, Trade
    • Sales Questions
    • Off Topic
    • Educators
    • Technical Based Off-Topic Discussions


  • Community Calendar

Find results in...

Find results that contain...

Date Created

  • Start


Last Updated

  • Start


Filter by number of...


  • Start





Website URL







Found 12 results

  1. Hi, I have a few questions in this task. 1. What is the best Arduino board package to use for the Wi-FIRE board? a. b. Both seem to run the basic blink sketch. I lean toward b. since I can specifically select "Wi-FIRE (rev.C)" Just wonder if Digilent is fully up-to-date with Wi-FIRE since they still are teaching how to use MPIDE, and states
  2. Hi, When I move the jumper to 5V on JP1-3.3V/5.0V Shield Voltage Select J1-Shield Power Connector goes from 3.24V -> 0V "The 5 V regulator can be completely disabled if it is not needed for a given application." Is that done with J15(rev.D)/J16(rev.C)- 5.0V Regulator Configuration. By moving both jumpers to the right? Thats how I am getting 0V on the shield power pin. If I move both jumpers to the left, I get 3.85Volt on the shield power pin, but that is still far from 5.0Volt! I can't "easily" find a description of how the many jumpers work on the Wi-Fire. I
  3. I'm working with the chipKIT Wi-FIRE board (Rev C) along with the newest version of the arduino IDE and the Digilent Core. I was wondering if it was possible to set up an ad hoc network hosted on the Wi-FIRE board that can be connected to from other devices, I've looked through various parts of the different WiFi related libraries in the core and have found several references to ad hoc but nothing about how I might set it up or what needs to happen to broadcast an SSID for other devices to see. Any help would be greatly appreciated.
  4. I am trying to come up to speed on the Wi-FIRE board and noticed that there is are two examples under the DSPI library that is included as part of the ChipKIT core hosted on the github site compared to the Digilent Core that is referenced on this page: Is there a particular reason why the DSPI_Demo sketch was not included in the Digilent core, but is part of the ChipKIT core. (Also makes me wonder what other differences may be lurking, left to be discovered.) It would appear that the two cores have
  5. I've been looking over the SD library that was installed as part of the chipKIT boards (ver 1.4.1) and I get the distinct impression that it implements the SPI protocol to the SD card using bit-banging, rather than a PIC32 SPI peripheral. Is this correct? Assuming so, are there any Arduino-compatible libraries for the Wi-FIRE that utilized the SPI peripherals? Assuming not, is my best be to go with MPLAB Harmony? (I'm an old MPLAB-X guy using version 2.10 and an old peripheral library)
  6. I am using a chipKIT Wi-FIRE Rev C board under Arduino 1.8.2 and there are three entries under Tools > Boards. The "Rev A &B, no FPU" is clearly not the correct one, but there is a "chipKIT wifire" and a "chipKIT wifire 80MHz". Since the Rev C board comes with a PIC32 that has a 200 MHz core, I'm guessing the first one is the correct choice, is that correct? Would have made more sense to label the board files by the revision label, rather than clock frequency ...
  7. I have a Wi-FIRE rev C board that I would like to program from the Arduino IDE. According to the ChipKIT wiki, the ChipKIT core has replaced the need for MPIDE. I hooked up the Wi-FIRE to the UART mini-USB on the top of the board (Call out 26 in the ref manual) and then tried to program from the Arduino IDE by selecting "Sketch > Upload" but I get an the following error Programmer for Microchip PIC32 microcontrollers, Version 2.1.24 No target found. Copyright: (C) 2011-2015 Serge Vakulenko An error occurred while uploading the sketch My guess is that I need to use my chi
  8. Hi, Currently I have an issue when I connect the Wi-Fire to wireless network using UDP protocol. It will be helpful if is some information about the fuctions availables on the libraries <DEIPcK.h> and <DEWFcK.h>. On this moment my target is to solve the error received from "IsIPStatusAnError(status)". I'm not sure which configurations are necessary to solve the error, the error is attached . This error comes when the following code trys to work. Could you give me information available to use the UDP protocol used on the sketch named "UDPEchoClient .pde"? Code involv
  9. As I work with the chipKIT WF32 and the WiFIre, I find that making external connections to these processor boards is not as convenient as they are for the chipKIT Pro MX7 that has Pmod connectors JA through JF. Additionally there are limited pins for taking 3.3V/5V and ground off board. I can only assume that these chipKIT boards were always intended to be used with a shield of some sort. If Digilent makes IO shields specifically for the WF32 and WiFire, please advise. Meanwhile, I find the the Pmod Shield-Uno can be used to provide standard Pmod connections provided a few modification
  10. Hi, I liked my WF32 so much i bought a uC32 and a Wi-Fire. Had a little issue with the uC32 board but got that resolved in an other post. Now the Wi-Fire will not read the SD Card but the WF32 can. The wi-Fire can connect to the network but cannot display a server page as it fails to initialize or read the SD card. I have been looking all over the forums for info but cannot find any info i understan about the Wi-Fire and SD card. Is there a simple way to test to see if my problem is software or hardware. I was using the deWebIOServer packare I found with an WF32 instructable. This works well
  11. Does anyone know if AnalogShield will work on the new ChipKit Wi-FIRE (with few modifications) ? I look inside the library and I saw several " #ifdef __PIC32MX__ " However the new ChipKit WI-FIRE is " PIC32MZ ", MZ not MX. In other words, without any modification it will not work. However, if the chip is similar, as described in this forum, should be easy. Thanks