Search the Community

Showing results for tags 'uno'.



More search options

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • News
    • New Users Introduction
    • Announcements
  • Digilent Technical Forums
    • FPGA
    • Digilent Microcontroller Boards
    • Non-Digilent Microcontrollers
    • Add-on Boards
    • Scopes & Instruments
    • LabVIEW
    • Other
  • General Discussion
    • Project Vault
    • Learn
    • Suggestions & Feedback
    • Buy, Sell, Trade
    • Sales Questions
    • Off Topic
    • Educators
    • Technical Based Off-Topic Discussions

Calendars

  • Community Calendar

Found 4 results

  1. Hi, I have purchased the Multi-Touch Display Shield, see link below for actual model. https://reference.digilentinc.com/reference/add-ons/mtdshield/start I have downloaded the Arduino IDE folder, installed the mtds & MyDisp libraries and followed the QuickStart.txt. When I open an example from either of those libraries and attempt to compile, it fails and lists loads of errors (Please see .txt file attached where I have copied error messages). I have my Arduino Uno selected and the libraries installed, there are errors in the followings directories: \Arduino\libraries\MyDisp\Examples\MyDispDemo\MyDispDemo1\MyDispDemo1.pde \Arduino\libraries\mtds\MtdsCore.cpp \Arduino\libraries\mtds\MtdsFs.cpp \Arduino\libraries\mtds\MtdsHal.cpp Does anyone know what is causing this, I have tried both Arduino 1.6.9 & 1.8.5 but it shows the same errors. Any help would be appreciated. Thanks, Evan Error compiling for board ArduinoGenuino Uno - Error Message.txt
  2. Hello, I have some questions about the Analog Shield: - What is the dimension of an analog shield plugged on top of an Arduino Uno? (Total dimension of the assembly, for planning the size of the enclosure) - What is the pitch of the headers on top of the board, where the AO pins are routed? Is it standard 2.54-mm pitch? Is there a guide somewhere what is the location of these headers for plugging some boards in them? (Like for routing some BNC plugs to the wall of the box) - A very stupid question in the end: do I need to separately power the Analog shield when coupled with an Uno, or it can get enough supply from the pins of the Arduino? Thanks
  3. Hello, I am working with the chipKIT Max32, chipKIT Network Shield, and ti / Stanford Analog SHIELD from Digilent. I need to be able to generate various analog signal remotely (Ethernet). I have not been successful using the Analog SHEILD with the Max32 (much less the addition of the Network Shield). However, using my Arduino Uno, I am able to generate a signal using the "passthrough" and "ramp" example with the Analog Shield. I would continue to use the Uno, however, I need the extra digital I/O the Max32 (Mega format) has to offer. Also, I have verified basic communication with Max32 using the "blink" example. 1) What is the probable cause of my failure with the Max32 versus the Uno? 2) What corrective action should I take? Boards in use: Max32 Rev E, Analog SHIELD Rev D, Network SHIELD Rev C Software: passthrough and ramp examples included with the Analog Shield library, Arduino IDE 1.6.13 Note: I had looked at using MPIDE with the chipKIT Max32, but the website for MPIDE recommended the most up version of the Arduino IDE. So, MPIDE is one option (of which I am aware) I have not tried, yet. Thank you for any assistance you can offer.
  4. Good Day, I'm thinking of picking up the LabView Physical Computing kit that includes the Microchip PIC...i.e. the ChipKit WF32. I saw that there is a PMOD shield for the UNO standard, but it doesn't say specifically that it is supported on this ChipKit board. It only mentions some of the older boards. Does this shield work properly with this ChipKit? It would be great if it did, as I have a ton of PMODs that I bought for my Nexys4 DDR. My son would love to use them with ChipKit. Thanks, Dave