Search the Community

Showing results for tags 'temperature sensor'.



More search options

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • News
    • New Users Introduction
    • Announcements
  • Digilent Technical Forums
    • FPGA
    • Digilent Microcontroller Boards
    • Non-Digilent Microcontrollers
    • Add-on Boards
    • Scopes & Instruments
    • LabVIEW
    • FRC
    • Other
  • General Discussion
    • Project Vault
    • Learn
    • Suggestions & Feedback
    • Buy, Sell, Trade
    • Sales Questions
    • Off Topic
    • Educators
    • Technical Based Off-Topic Discussions

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


AIM


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


Location


Interests

Found 2 results

  1. Hello, I am kind of new to FPGAs and I am trying to use the XADC in order to monitor the temperature sensor: I am using Vivado 2018.2, Nexys video as a board. I used the IP catalog in order to set up the XADC as following: DRP, Single channel, continuous, disable all alarms, disable reset_in, channel to monitor: temperature I wrote a top level module which reads the bits 4 up to 7 from do_out and light up LEDs accordingly: //part of the top module: module top( input CLK100MHZ, input vp_in, input vn_in, input [1:0] sw, output reg [11:0] LED ); wire enable; wire ready; wire [15:0] data; reg [6:0] Address_in; xadc_wiz_0 XLXI_7 (.daddr_in(Address_in), //addresses can be found in the artix 7 XADC user guide DRP register space .dclk_in(CLK100MHZ), .den_in(enable), .di_in(0), .dwe_in(0), .busy_out(), .vn_in(vn_in), .vp_in(vp_in), .alarm_out(), .do_out(data), .eoc_out(enable), .channel_out(), .drdy_out(ready)); always @( posedge(CLK100MHZ)) begin if(ready == 1'b1) begin case (data[7:4]) 4'b0001: LED <= 12'b000000000001; 4'b0: LED <= 12'b0; 4'b1000: LED<=12'b000000000010; default: LED <= 12'b1; endcase end end ///// I have one problem though, as I come to set the address of the ddr_in as done in a documentation found here which has LEDs displaying potential differences monitored by XADC, I do not understand what 8 bit address I should assign for the DRP to monitor the Temperature Channel ! "Address_in <= 8'h ????" My goal: I need the LEds to display something for the sake of demonstration that I am able to read values out of the do_out. Thank you for your help.
  2. Hi there, I am using the chipKIT Wi-FIRE with the basic I/O shield and MPLABX IDE. I want to read out the temperature sensor of the I/O shield via I2C and write the value to the OLED display. I do see a value on the OLED-display that reacts on the sensors environment (i.e. it increases when I put my finger on the sensor), however it is clearly wrong as I get 360°C for room temperature (before anyone asks: I know I have to multiply the sensor value with 2^-4 to get a the correct numerical value). To initialize the bus and read out the sensor value I followed an example found on https://sites.google.com/site/johnkneenconnectedlab/i2c, but it goes much beyond what I actually want to accomplish and modifying that code just leads to the result mentioned above. So here is my question: is there some starter code to simply read out the temperature sensor in this setup?