Search the Community

Showing results for tags 'teensy'.



More search options

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • News
    • New Users Introduction
    • Announcements
  • Digilent Technical Forums
    • FPGA
    • Digilent Microcontroller Boards
    • Non-Digilent Microcontrollers
    • Add-on Boards
    • Scopes & Instruments
    • LabVIEW
    • FRC
    • Other
  • General Discussion
    • Project Vault
    • Learn
    • Suggestions & Feedback
    • Buy, Sell, Trade
    • Sales Questions
    • Off Topic
    • Educators
    • Technical Based Off-Topic Discussions

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


AIM


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


Location


Interests

Found 2 results

  1. I am trying to get the PMOD PMON1 to run on a teensy for a micro project I am working on and so far not so good. Here is my code block, please take a look and let me know if you see anything I am missing? I far I am not Serial reading anything but the "Program Started". /* ADM1191 U/I I2C converter I2C SDA ==> 18 I2C SCL ==> 19 CONF_REG[7..0] NC STATUS_RD NC VRANGE I_ONCE I_CONT V_ONCE V_VCONT V_VCONT =1, countinuosly cnv V I_VCONT =1, countinuosly cnv I VRANGE Vrange =0 -> Vr=26.52V, write I2C [ADR][CONF_REG] read I2C [ADR][Uh][Ih][Ul:Ih] */ #include <Wire.h> #define ADM1191_ADR B01100000 // 7bit ADM1191 device address A1,A0=00 jumpers set to 1 0Xb00 #define ADM1191_CONF_REG B00000101 // ADM config uint16_t result_Uh=0, result_Ih =0, result_UIl =0; float P, Uh, Ih, Rs=0.05; void setup() { while(!Serial); Serial.print("Program Started"); Serial.println(); Serial.begin(9600); Wire.begin(); Wire.beginTransmission(ADM1191_ADR); Wire.write(ADM1191_CONF_REG); Wire.endTransmission(); } void loop() { Wire.beginTransmission(ADM1191_ADR); Wire.requestFrom(ADM1191_ADR, 3); // request 3 bytes from ADM while(Wire.available()) { result_Uh = Wire.read(); // HIGH U result_Ih = Wire.read(); // HIGH I result_UIl = Wire.read(); // LOW U : LOW I result_Uh = (result_Uh << 4) + (result_UIl >> 4); result_Ih= (result_Ih << 4) + (result_UIl & 0x0F); Uh= (26.52/4096)* result_Uh; Serial.print(" U: "); Serial.print(Uh, 2); Serial.print(" [V]\t"); Ih= ((105.84/4096)*result_Ih)/Rs; Serial.print(" I: "); Serial.print(Ih, 0); Serial.print(" [mA]\t"); P= Uh*Ih/1000; Serial.print("P: "); Serial.print(P, 2); Serial.println(" [W]\t"); } Wire.endTransmission(); delay(1000); }
  2. I am trying to work the PMODALS off of a Teensy 3.1. I was wondering if any one has gotten this connected and working? If so could you reply with your .h file. The DSPI is not compatible with the Teensy and converting this to arduino SPI does not seem to be working. Thanks!