Search the Community

Showing results for tags 'ruggeduino'.



More search options

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • News
    • New Users Introduction
    • Announcements
  • Digilent Technical Forums
    • FPGA
    • Digilent Microcontroller Boards
    • Non-Digilent Microcontrollers
    • Add-on Boards
    • Scopes & Instruments
    • LabVIEW
    • Other
  • General Discussion
    • Project Vault
    • Learn
    • Suggestions & Feedback
    • Buy, Sell, Trade
    • Sales Questions
    • Off Topic
    • Educators
    • Technical Based Off-Topic Discussions

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


AIM


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


Location


Interests

Found 1 result

  1. Hello Digilent community, I'm running an analog shield on an arduino uno (well, actually an Ruggeduino SE, but I understand they would operate the same here). Arduino 1.8.2 I'm reading from two sensors and reporting data to the terminal.The board is attached to and powered by usb (which reads ~4.75 V): The sensors are powered form the Analog shields +5/-5 V rails. 1) A thermistor that is dropping over a 10K resistor on analog channel 0. The analog shield reports the thermistor reading ~48150 A/D counts when it reads ~2380 mV with the multi meter. 2) an ion selective electrode another sensor that outputs -150 to +150 mV on analog channel 1. The sensor reads ~33070 counts and 55 mV with the multimeter I would like to know the transfer equation to convert the A/D count so that I can compare the analog shield reading to my multimeter. The sensors have been characterized in the voltage domain so I would like to convert the A/D counts to volts so that I can convert the sensor readings to engineering units (celsius, etc).This is a newb question, yes - I don't have any experience with bipolar sensors and A/D converters. Typically the transfer function for A/D to volts is something like this: Equation 1 (from googling around): Volts = ((A/D reading / (Nbits-1))* Vfullscale) - Vfullscale/2 For this system I've gathered the following info from the datasheets and docs: Nbits -1= 2^16 -1 = 65535, Vfullscale = 10V (5V to -5V), Are these values correct? Should I change them to the bus voltage that is measured (for example, change 5V to 4.75V when plugged into USB)? Plugging these values in for the thermistor reading I get: 2347 mV, an error of ~1.5%, not bad. Plugging these values in for the ion selective electrode reading I get: 46.2 mV, an error of ~16%. Do these error magnitudes seem acceptable to you? I'll likely re-characterize sensors with this platform as it will deployed rather than relying on the previous sensor characterizations done with a multimeter. I'd like to know if this is this the correct approach to convert A/D counts, and if so, suggest it be added to the example code or documentation to help others. If not, please let me know how and where I'm in error. Here is the code: //include libraries #include <analogShield.h> //Include to use analog shield. #include <SPI.h> //required for ChipKIT but does not affect Arduino\ //Defines // which analog pin to connect #define THERMISTORPIN 0 #define ISEPIN 3 // full scale voltage (5V- -5V) #define VFS 10.0 //loop delay time in ms #define DELAYTIME 1000 //16 bits (0 to 65535) #define NBITS 65535.0 void setup() { Serial.begin(9600); } void loop() { // read data from A/D double ISE_counts = analog.read(ISEPIN); double therm_counts = analog.read(THERMISTORPIN); //Convert A/D counts to volts double ISE_volts = ((ISE_counts / NBITS) * VFS) - VFS / 2; double therm_volts = ((therm_counts / NBITS) * VFS) - VFS / 2; //print data to the terminal Serial.print("Average temperature voltage: "); Serial.println(therm_volts); Serial.print("Average ISE voltage: "); Serial.println(ISE_volts); delay(DELAYTIME); } Thanks in advance,