Search the Community

Showing results for tags 'novice'.



More search options

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • News
    • New Users Introduction
    • Announcements
  • Digilent Technical Forums
    • FPGA
    • Digilent Microcontroller Boards
    • Non-Digilent Microcontrollers
    • Add-on Boards
    • Scopes & Instruments
    • LabVIEW
    • FRC
    • Other
  • General Discussion
    • Project Vault
    • Learn
    • Suggestions & Feedback
    • Buy, Sell, Trade
    • Sales Questions
    • Off Topic
    • Educators
    • Technical Based Off-Topic Discussions

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


AIM


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


Location


Interests

Found 1 result

  1. Greetings everyone, This is the first ever post of a beginner who has set on the path to learn embedded systems. Please forgive me if haven't followed rules of posting. I took the embedded system plunge few weeks back. Bought a strong laptop, a Zybo board, OV7670 camera, installed Vivado. Read online tutorials like 'blinking LEDs' and 'HDMI-to-VGA out' (and the others ones in Zynq Book) to get myself accustomed with Vivado etc. [Abbreviations in the text: PS= Processing System, PL= Programmable Logic] I have been visiting a blog lately and have found that quite helpful. A couple of weeks back I started this project mentioned on the same blog (http://lauri.võsandi.com/hdl/zynq/xilinx-vdma.html). What I'm doing is a bit simpler version of this as I omitted some part of the design which I thought wasn't required, I'll mention about that later. Pretty much like a mixture with another project involving test pattern generator (http://lauri.võsandi.com/hdl/zynq/xilinx-video-capture.html) My aim in this project is to get the stream from OV7670 camera, take it through PL (AXI VDMA IPs) to the PS, and then view the stream inside some window within Xillinux (linux). I feel doing so will ensure a bit of learning in both the PL and PS. Following is my progress along with doubts I have so far: 1- I have pasted the picture of my block design (called VDMA_Trial). After playing hit and trial, I managed to go around all the initial errors and successfully generated the bitstream. Which was a big relief. If you compare my block design with the one mentioned on the link I pasted above, you'll notice mine has lesser number of IP blocks. I did not need the RGB, HSYNC and VSYNC outputs from the PL so I omitted that part and only focused on taking the camera stream to the PS. Do you think this makes sense? Or do I need to have the complete IP blocks even if I don't wish to see the stream on HDMI (or VGA)? 2- I'm a normal computer user who has used Windows PCs most part of the life. So I don't have much idea of CLI based Linux. After reading from online resources, I booted Xillinux image (downloaded from xillybus.com) on the Zybo through SD card. Since I wish to watch the stream from the camera inside the GUI Xillinux. From a bit of reading I got to know about something called V4L2, which I'm still trying to figure how to install on Xillinux. Now assuming the design in point 1 is fine, can I simple paste the bitstream of the project in the SD card along with the Xillinux boot files (there are some other files in SD card too for Xillinux: devicetree, ulmage and xillydemo.bit). Will the hardware design in the PL activate and start writing the video stream information to the PS memory (DDR) when I boot up the Zybo with this SD card? If not, what step must I follow? Do I need to launch SDK to write some code to tell PS what to do? But I will already have the Xillinux OS running on PS, am I correct when I say I'll have to write and compile some code in Xillinux to tell PS to fetch the stream which is being written to PS memory by VDMA (from PL). 3- While reading different stuff, I came across this thing related to V4L2 and OV7670 (http://www.cs.fsu.edu/~baker/devices/lxr/source/2.6.31.13/linux/drivers/media/video/ov7670.c). To a layman like me, it looked like the code to set up OV7670 camera using V4L2 driver. Will I need to compile and run this code in Xillinux to watch the stream? I tried, but it just did not compile. My apologies for making it long and prob'ly silly. Just started traversing a steep learning curve, will take time to learn. I really look forward to seeing your enlightening responses. If there's any more info you need please let me know (in easy English ). Regards, Haris.