Search the Community

Showing results for tags 'hid'.



More search options

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • News
    • New Users Introduction
    • Announcements
  • Digilent Technical Forums
    • FPGA
    • Digilent Microcontroller Boards
    • Non-Digilent Microcontrollers
    • Add-on Boards
    • Scopes & Instruments
    • LabVIEW
    • FRC
    • Other
  • General Discussion
    • Project Vault
    • Learn
    • Suggestions & Feedback
    • Buy, Sell, Trade
    • Sales Questions
    • Off Topic
    • Educators
    • Technical Based Off-Topic Discussions

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


AIM


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


Location


Interests

Found 4 results

  1. Hi Digilent staff, and fellow forum members, Just wondering if you guys had considered making a USB HID -> PS/2 PMOD board? I was thinking of something like the circuit on the Nexys 3,4 boards which uses a PIC to convert a USB keyboard to PS/2 compatible signals. Would be handy for using newer USB keyboards/mice on PMOD socket equipped FPGA boards. PS/2 devices are becoming harder to find brand new. I (for one) would be interested in a few. Kind regards, Leslie
  2. fpga_babe

    HID protocol on Basys3

    Hi, I am using Basys3 board and I want to write a RTL module in FPGA to get the character from USB Keyboard. From the Digilent reference of basys3, if the FPGA side only receive the data from Keyboard, then the PS_CLK and PS_DAT ports can be as input direction. My question is that, to receive the keycode from a keyboard, do we need to send configuration to Keyboard before hand ?
  3. Good day everyone! I need help on programming the Nexys 3 using a USB memory stick. Here is what I tried so far: 1. Save a single .bit file to a USB memory stick. I have tried my own .bit files as well as the Digilent's Built-In Self Test. I have also tried two USB flash drives. 2. Connect two jumpers on the mode switches. I have also tried none and mode 0 only. 3. I then attached the USB flash drive to the Nexys 3 and press the reset button. But unfortunately the bit file does not get programmed to the FPGA. The <busy> LED beside the USB port on the Nexys 3 is forever blinking at a slow rate. Does anyone tried configuring the Nexys 3 using a USB flash drive? Thank you. Note: I tried it on another Nexys 3 board but also fails to load the bit file. Regards, Nico C.
  4. Hello, After downloading the project code found here: https://reference.digilentinc.com/learn/programmable-logic/tutorials/nexys-4-ddr-keyboard-demo/start and programming my Nexys4 DDR, I can not get my board to read keyboard inputs. I've tried three different USB keyboards (Apple, Razor, and Logitech). To make sure that there was nothing wrong with the USB port, I performed the selftest as specified in the manual: "Connecting a mouse to the USB-HID Mouse port will allow the pointer on the VGA display to be controlled. Only mice compatible with the Boot Mouse HID interface are supported." One of the mice I tested allowed me to move the pointer on the VGA display. This leads me to believe that the USB port on my board is working. So I have three questions moving forward: Do I need a specific jumper configuration to read keyboard input? Does anyone know of a make/model of keyboard which is guaranteed to work with the board? Are there any self tests to show that keyboard input is indeed being received? I found this in the manual under section 3.3 of the reference manual: "For example, if a USB keyboard is plugged in, a rapid blink will signal the receipt of an HID input report from the keyboard." However, its placement in the manual leaves me uncertain that it is in fact a built in self test. That is, I am unsure if a keyboard plugged in during the demo configuration will make the "busy" light blink rapidly. Thank you.