Search the Community

Showing results for tags 'console'.



More search options

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • News
    • New Users Introduction
    • Announcements
  • Digilent Technical Forums
    • FPGA
    • Digilent Microcontroller Boards
    • Non-Digilent Microcontrollers
    • Add-on Boards
    • Scopes & Instruments
    • LabVIEW
    • FRC
    • Other
  • General Discussion
    • Project Vault
    • Learn
    • Suggestions & Feedback
    • Buy, Sell, Trade
    • Sales Questions
    • Off Topic
    • Educators
    • Technical Based Off-Topic Discussions

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


AIM


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


Location


Interests

Found 4 results

  1. When running from Xilinx SDK (2018.3) I cannot get the trivial "Hello world output" from my Zybo Z7 board. However I do get the following messages: Connected to /dev/ttyUSB1 at 115200 Initializing... init:done Zybo Z7-20 Rev. B Demo Image This means that I in general can talk to the port that appears in /dev most often as /dev/ttyUSB1 but at times under different number, so the problem is different from just being unable to get serial port working. The port was initially not accessible due permissions but I have worked around by changing them with chmod. I also added myself to dial group by s'udo adduser audrius dialout' . This has no effect. I have created the "Base Zynq" project with Vivado, generated bitstream without any changes to it, exported (Export hardware, include bitstream) and opened SDK using Vivado menu commands under "File" group. In SDK, I asked to create a new application project, standalone platform, "Hello world". I have selected "Program device" in SDK and passed this step without any obvious errors, with progress bar gradually moving as device is programmed. Also, Vivado shows the device temperature correctly. I noticed that when I do the device programming, the demo LEDs stop flashing in all colors. Only red LD13, green LD12 and green LD4 remain on. However when I attempt to run the project from SDK, multiple LEDs start flashing again, indicating that probably a reset has happened. At this point the "Zybo Z7-20 Rev B Demo Image" appears on the SDK terminal (115200 bauds) , so the terminal in general works. Looks like another "debug terminal" for two cores opens in SDK (TFC Debug Virtual Terminal cores 1 and 0) at this point but also remains empty. I have tried to change the stdout in BSP settings, but switching between "ps7_uart_1" and "ps7_coresight_com" results no changes in behavior. I tried to move the jumper JP5 between JTAG and QSP1. The "Demo image" message shows up in QSP1 position. In JTAG position, just nothing appears. I also tried to flash the bitstream from Vivado directly but this did not change anything. I have no problems in getting the output from KCU116 Microblaze after the similar sequence of actions but this is on another host (Window 7). I am using Ubuntu 16 (4.15.0-43-generic #46~16.04.1-Ubuntu SMP Fri Dec 7 13:31:08 UTC 2018 x86_64 x86_64 x86_64 GNU/Linux) I attach SDK logs and synthesis logs. Board files I have downloaded from https://github.com/Digilent/vivado-boards/archive/master.zip. After installing as described in https://reference.digilentinc.com/vivado/installing-vivado/start I was able to find and select the Zybo Z7 - 20 after restarting Vivado. While the board was initially powered by USB 3, I tried the 5 V wall adapter later, no changes. Last think I tried was connecting the pin aux_reset_in of the block rst_ps7_0_50M to constant value 1 in Vivado designer. It looks like reset signal with active low, so, thought, maybe not a good idea to left hanging as it is initially created. Yet was not helpful. Summarizing, looks like the demo image boots, and the card can be accessed and programmed by Xilinx tools, also serial port works, but the "Hello world" from SDK does not run at all or crashes immediately after start. sdk.log synthesis.log
  2. Hello, just plugged in my new Zybo Z7 471-015 but cannot connect to serial port. It works on the Zybo. PROG UART is connected to USB PC BSP stdin, stdout is set to ps7_uart_1 I have no other application open that is accessing the serial ports to make sure I dis- and reconnected the Zybo Z7, still doesn't appear on the port list Zybo Z7 appears as USB Serial Converter A and B in the device mngr restarted PC tried another USB port replaced USB cable, both are data cables JP6 is set to USB JP5 is set to JTAG drivers had been installed with Vivado 2017.2 re-installed Vivado 2017.2 cable drivers, restarted PC USB port should be listed even without any PL configuration loaded, right?
  3. I started this post and got a good response. I was able to use jpeyron's project (Hi Jon) to get the Zybo Getting Started to turn on LEDs with the switches. However, I still cannot get any output on any console. I am sticking with his project until I get this console business sorted out. Here's what I have: Vivado 2016.4 on a 64-bit Ubuntu 16.04. I'm trying this: https://reference.digilentinc.com/learn/programmable-logic/tutorials/zybo-getting-started-with-zynq/start and I do indeed have the correct board activity (LEDs and switches). On power on, I see this: abc@Kassandra:~$ lr /dev/ttyU* ls: cannot access '/dev/ttyU*': No such file or directory turn on the Zybo and: abc@Kassandra:~$ lr /dev/ttyU* crw-rw---- 1 root dialout 188, 1 Sep 14 18:08 /dev/ttyUSB1 So it looks like it's ttyUSB1. I am in the dialout group. I have tried, minicom, screen, putty, and cutecom, all with /dev/ttyUSB1, 115200, 8, none, 1, and I've played around with the flow control. If I type anything in the console I see the Zybo board's TX led flash. So it's the right port and I can program the board, and the SW is running on the Zynq. But I never get anything out on the console. The "getting started" is meant to tell me via the console which button I pushed (and that's something I so want to know). I have read and tried about 20 different "solutions". Any help appreciated as I have had zero success. Specific question: For anyone else with Vivado 2016.4 on a 64-bit Ubuntu 16.04, have you had to install the Digilent Adept SW to get this working? Any help appreciated as I have had zero success and for the first time in my many years I'm thinking about Altera. GogMagog
  4. I am currently using nexys 4, I want to input console inputs to my VHDL design. I know that ISE uses a .ucf file where the inputs and outputs of the card are assigned, however my interest is not to use the inputs provided by the card and I do not know how to assign these inputs sent from an application, I would thank anyone who can help.