Search the Community

Showing results for tags 'configuration'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


  • News
    • New Users Introduction
    • Announcements
  • Digilent Technical Forums
    • FPGA
    • Digilent Microcontroller Boards
    • Non-Digilent Microcontrollers
    • Add-on Boards
    • Test and Measurement
    • LabVIEW
    • FRC
    • Other
  • General Discussion
    • Project Vault
    • Learn
    • Suggestions & Feedback
    • Buy, Sell, Trade
    • Sales Questions
    • Off Topic
    • Educators
    • Technical Based Off-Topic Discussions

Find results in...

Find results that contain...

Date Created

  • Start


Last Updated

  • Start


Filter by number of...


  • Start





Website URL







Found 7 results

  1. Hi, I'm looking to test out if I can send a bitstream to the artix7 Fpga from a Linux processor. To do so, I need to set all the mode pins to 3v3. In the schematic sheet for arty, I cant see from where the mode pins get connected to the fpga. My plan is to do a little circuit surgery to remove the spi flash. Would anyone be able to tell me how the mode pins hookup? Best, Konstantin
  2. Currently we are using Nexys Video Development Board which is having many features and peripherals. Now we want to make our custom board with limited peripherals. We would like to use only 2 Configuration modes - JTAG Progamming and Quad-SPI Flash Memory Mode. We are not looking for SD Card and USB Programming mode. In Reference Manual Configuration Diagram, There is one PIC14 Controller available, We have confusion about is requirement? Is it necessary to have if we are not using SD Card and USB Progamming mode? It will be great help if you can direct us in this regard. We are not
  3. I just got a Nexys 3 board and I'm very excited to get started working with it! Seems like a wonderful device. Sadly I have not gotten off to a good start due to software and documentation problems. I am very familiar with digital logic and electronics and have been a professional software developer for over 20 years. I have not worked with an FPGA before but I understand what it is. The board powers up and self tests connected to USB on my Windows 7 device. It's not clear which software I'm supposed to use to configure and test it. My understanding from reading the docs is tha
  4. I'm trying to configure the Discovery2 with BNC adapter to transmit three different clock-synchronized pulses to three interacting pieces of equipment via the BNC. I'm aiming for precise independent control of waveform, frequency, pulse-width, triggers, etc, all from the same master clock. I need precise pulse timing integrity at the khz level, with minimal degradation over 30ft+ cable distances, hence why we are aiming to use the AWG on the BNC rather than the pattern tool on DIO pins in WaveForms. The BNC Adapter for the Discovery2 is configured with two input and two output ports. Is
  5. vishnu

    DDR3 configuration

    Hello Everyone, This is Vishnu , FPGA Design Engineer. I need help from you, in my project I need to get data into DDR from camera and has to given for another data processing module. Here I have some doubts regarding storage . 1) As camera is line scanning camera , Is it possible to store line information from camera (line-by-line) and to access it full line-by-line directly.(data is of 12 bit). 2) How many cycles will be delayed if configuration is done with Microblaze . 3) Help me out some links for the configuration to do in customized version.
  6. I have LabVIEW 2014 and LINX 3.0. The entire installation process went as expected. However, when trying to setup the PI 3 as indicated in timestamp 3:50 of this video: Under the menu: Tools >> Makerhub >> LINX... All I get is: Generate Firmware Libraries LINX Firmware Wizard myRIO Support I don't have the option: LINX Target Configuration Any ideas?
  7. Hello, I am trying to configure an RN-42 PmodBT2 module using puTTY following these steps: { $$$ SM,2 SR, MAC ADDRESS C, MAC ADDRESS } the MAC ADDRESS refers to the address of the device I want the module to connect to it. When I enter the command C, MAC ADDRESS, I get an error, ERR-Connected. and if I entered GF to know the address of the last connection I get a random address starts by 088EDB -its not the address of my laptop either-. Another problem is that if I tried to disconnect the device using K, ADDRESS the command window hangs and I ha