Search the Community

Showing results for tags 'arty-z7'.

More search options

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


  • News
    • New Users Introduction
    • Announcements
  • Digilent Technical Forums
    • FPGA
    • Digilent Microcontroller Boards
    • Non-Digilent Microcontrollers
    • Add-on Boards
    • Scopes & Instruments and the WaveForms software
    • LabVIEW
    • FRC
    • Other
  • General Discussion
    • Project Vault
    • Learn
    • Suggestions & Feedback
    • Buy, Sell, Trade
    • Sales Questions
    • Off Topic
    • Educators
    • Technical Based Off-Topic Discussions

Find results in...

Find results that contain...

Date Created

  • Start


Last Updated

  • Start


Filter by number of...


  • Start





Website URL







Found 4 results

  1. I seem to be having a similar issue with my Arty Z7 as this poster. At one point, my board was booting just fine from flash (via QSPI) or an SD card (with FSB, bistream, and SDK program). However, something happened along the way and I have to press the PROG button every time I power it up to boot it (true for either QSPI flash or SD). Only after I do this does the DONE light light up and the SDK program runs. My bitstream isn't compressed and I'm using Vivado 2018.2. I haven't messed with any of the bitstream or device properties. Any ideas? Thanks!
  2. Hello Everyone, I am trying to get Arty Z7-20 boot from flash with encryption enabled. I am following Xilinx 'XAPP1319' to program AES key to BBRAM. I created MCS boot image with 'fsbl' and 'program_aes_key_bbram' application program(xilskey 6.3 example 'xilskey_bbram_example' for Zynq not ZynqMP) for qspi flash as described in Xilinx 'XAPP1319'. However on booting from SPI flash, BBRAM example print exit message 'BBRAM Example failed' on serial console. On debugging with JTAG, I found it fails while programming BBRAM, in function I have the jumper set to QSPI while booting from flash. Attached is serial console output. Any idea why I am having this issue? bbram_out.txt
  3. Hi All, I am trying to build HDMI In Demo on Arty z7-20 board in Vivado SDK 2018.1, but it failed with the following error messages shown in the console. Can anybody tell me where to find xil_types.h file and why my setup doesn't have it? Thanks, Charles 12:36:42 **** Clean-only build of configuration Debug for project hdmi_in **** make clean make: *** No rule to make target 'clean'. Stop. 12:36:42 Build Finished (took 552ms) 12:36:43 **** Build of configuration Debug for project hdmi_in **** make pre-build main-build a9-linaro-pre-build-step Building file: ../src/video_capture/video_capture.c Invoking: ARM v7 gcc compiler arm-none-eabi-gcc -Wall -O0 -g3 -c -fmessage-length=0 -MT"src/video_capture/video_capture.o" -mcpu=cortex-a9 -mfpu=vfpv3 -mfloat-abi=hard -I../../hdmi_in_bsp/ps7_cortexa9_0/include -MMD -MP -MF"src/video_capture/video_capture.d" -MT"src/video_capture/video_capture.o" -o "src/video_capture/video_capture.o" "../src/video_capture/video_capture.c" In file included from ../src/video_capture/video_capture.c:105:0: ../src/video_capture/video_capture.h:74:10: fatal error: xil_types.h: No such file or directory #include "xil_types.h" ^~~~~~~~~~~~~ src/video_capture/ recipe for target 'src/video_capture/video_capture.o' failed compilation terminated. make: *** [src/video_capture/video_capture.o] Error 1 12:36:43 Build Finished (took 837ms)
  4. Hello, I want to use Arty Z7-20 for embedded computer vision project. So I tried to make platform file using and followed "SDSoC_Platform_creation_Guide.txt". But Platform make was failed because "Include directory 'C:/~~/SDSoC_Staging/include_linux' doesnt exist." I looked for "include_linux" folder on github repository but I couldn't find it. Where is "include_linux" folder? Or, Did I take any mistakes? I hope you will be able to provide the information. sdspfm.log Arty-Z7-20-base_src_others_SDSoC_Staging at master · sbobrowicz_Arty-Z7-20-base · GitHub.html