Search the Community

Showing results for tags 'arm'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • News
    • New Users Introduction
    • Announcements
  • Digilent Technical Forums
    • FPGA
    • Digilent Microcontroller Boards
    • Non-Digilent Microcontrollers
    • Add-on Boards
    • Scopes & Instruments and the WaveForms software
    • LabVIEW
    • FRC
    • Other
  • General Discussion
    • Project Vault
    • Learn
    • Suggestions & Feedback
    • Buy, Sell, Trade
    • Sales Questions
    • Off Topic
    • Educators
    • Technical Based Off-Topic Discussions

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


AIM


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


Location


Interests

Found 10 results

  1. Dear friends, We have intended to use the JTAG-SMT3-NC module for both FPGA and ARM MCU programming. Our planned configuration is channel A for FPGA programming and channel B for ARM MCU programming. Do you please notify us if we are capable to perform the above work or not? Also, can we configure as JTAG the both channels (A and B)of the JTAG-SMT3-NC module with FT_PROG software. If not, please advise the solution. Also you can submit your tender to eliminate this difficulty. Attached please find the our working configuration. Wait for your response.
  2. Howdy. I have what I think is a fairly basic question: Which (non-FPGA) processor boards support Pmod modules? Is there any chance to see a table that shows each of the current ARM and PIC32 processor boards down a left-hand column and then the quantity of each of the Pmod ports (of each different configuration) on the middle of the chart? Thanks
  3. Hello, losing my mind trying to install adept 2 arm.deb for the raspberry pi. I used the dpkg --install command to unpack the .deb file. I wasn't successful in finding any install.sh executable. Please help , thank you. ,Chad
  4. Hi people, What I mean is that, can I write a program such that it can program the FPGA while executing? Thanks!
  5. Hi, Actually i want to generate the device tree for the Zedboard.So on the way of doing this i found one prebuilt device tree for the Zedboard which is having following line :- chosen { bootargs = "console=ttyPS0,115200 root=/dev/mmcblk0p2 rw earlyprintk rootfstype=ext2 rootwait devtmpfs.mount=0 consoleblank=0"; linux,stdout-path = "/[email protected]/[email protected]"; } ; After following some tutorials i got some idead about .dts file contents but still i did not get the meaaning of each word in above lines. Also in some other .dts files from other sourc
  6. Hi, Following is the snippet from the device tree for the MicroZed Board. [email protected] { #address-cells = <0x2>; #interrupt-cells = <0x3>; #size-cells = <0x1>; compatible = "arm,cortex-a9-gic", "arm,gic"; interrupt-controller; num_cpus = <0x2>; num_interrupts = <0x60>; reg = <0xf8f01000 0x1000 0xf8f00100 0x100>; xlnx,irq-f2p-mode = "REVERSE"; linux,phandle = <0x3>; phandle = <
  7. Hello, I'm developing a bare metal application in Zybo for a subject this semester and I want to run two tasks in parallel taking advantage of the dual processor in the Zynq. I want to know how can I use the dual core capabilities of the Cortex A9 processor in the Zybo in a bare metal application, configuring it from Vivado. I found this tutorial in Xilinx documentation but it uses the EDK instead of Vivado. If you can lead me to more resources where I can learn how to do this I'll be really thankful. Thank you very much.
  8. Hi! I am currently working on a project which uses a particular version of an ARM Cortex M0. Therefore I can not use Xilinx' tools to debug the ARM core directely. Using a Nexys 3 with a Spartan 6 I am looking for other ways to debug it: In the ARM forum a user pointed out that ARM has a debugger platform called CMSIS-DAP. Does Digilent support this platform? I currently use a JTAG USB debugger from Digilent, does it support CMSIS-DAP?If not, do you know of any other possibility on how I could debug the ARM core directly and without using Xilinx tools?Any help is much appreciated!
  9. Hi, I am currently using Zybo board. I have followed the " Embedded Linux® Hands-on Tutorial for the ZYBO™ " tutorial. My question is how does the Zynq system works? Is it similar to Microblaze soft processor or is it just FPGA? I have done the same work in the tutorial using Microblaze processor and XIlinx ISE. I find in the specs that Zynq hosts 2 ARM cortex processors, I want to know when we run above the above tutorial are we using any soft processor or if we are using the ARM Cortex processor? My point is if any soft processor is involved we can eliminate it and use the ARM processors
  10. Hello guys, I'm working with Zybo SoC right now and I have a few questions which I couldn't find the answer anywhere. I am using petalinux in the card with the .bsp from digilent website (Petalinux 2014.2 Board Support Package). The thing is, I want to change/reprogram the PL many times but I want to do it from the Linux, e.g. using C program and configuration port /dev/xdevcfg. Is it possible to do it?When I use a command shell "cat <file-name>.bit > /dev/xdevcfg", I could reprogram the FPGA and I can see the result but I lost the control of the Linux. I couldn't access to the ARM v