Search the Community

Showing results for tags 'analogshield'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


  • News
    • New Users Introduction
    • Announcements
  • Digilent Technical Forums
    • FPGA
    • Digilent Microcontroller Boards
    • Non-Digilent Microcontrollers
    • Add-on Boards
    • Test and Measurement
    • LabVIEW
    • FRC
    • Other
  • General Discussion
    • Project Vault
    • Learn
    • Suggestions & Feedback
    • Buy, Sell, Trade
    • Sales Questions
    • Off Topic
    • Educators
    • Technical Based Off-Topic Discussions

Find results in...

Find results that contain...

Date Created

  • Start


Last Updated

  • Start


Filter by number of...


  • Start





Website URL







Found 9 results

  1. Hi all, I just got the AnlalogShield and its working like a charm. But I wonder if there is a chance to make this shield work on an Arduino Zero. It is supposed to work on an Arduino DUE, so I guess it should be just some software, library, modifications. Currently, when I connect a ZERO I cannot upload software to the ZERO because it says "chosen wrong processor type" Any ideas how to fix this? Thanks in advance, Ben
  2. Hi, I am trying to use the Analog Shield with the Arduino DUE. It compiles, but the board does do anything. With the analog shield plugged in the Due works as normal. all I do is include "#include <analogShield.h>" and upload to the board. then the board is dead like if it crashed on start up. when I remove the include line and recompile it works again. I am using the library found on this forum dated 6/6/2016. The board works well with my ChipKit uC32. Luc
  3. Hello everyone, and thanks in advance for reading this! On a current project, I’m working with a network of Arduino UNOs R3, each with an AnalogShield installed (to be precise, it’s 4 Arduinos+AnalogShields total, communicating over I2C). I immediately found a problem when I connected all their Vin ports together to a 12V power supply: they sourced too much current (my main power supply was reading more than 1 A!). So I quickly stopped that and tried connecting the 5V ports together to a 5V power supply. At first this was OK, but soon they started to source too much current again.
  4. I am working slowly on my project. I thought I might post what could be a useful DipTrace base layout for a shield to use with the Analog Shield on an Arduino Uno . It could even be useful to somebody making an unrelated shield for Uno by stripping out the P1, P2, and P3 headers on the left and adjusting the board outline. The component designations and pin numbers match those of the Analog Shield. My board may end up bigger than the Analog shield, but I have put a board outline into the file that matches the 2.1 by 3.1 inch dimensions of the Analog Shield. I think it is correct, b
  5. Does anyone know if AnalogShield will work on the new ChipKit Wi-FIRE (with few modifications) ? I look inside the library and I saw several " #ifdef __PIC32MX__ " However the new ChipKit WI-FIRE is " PIC32MZ ", MZ not MX. In other words, without any modification it will not work. However, if the chip is similar, as described in this forum, should be easy. Thanks
  6. I am posting a support question on the forum so I can answer it here to help out others that may have a similar problem. " I downloaded the latest analogshield library from git hub. I'm trying to get the following code to compile in MPIDE: #include <analogShield.h> //Include to use analog shield. #include <SPI.h> //required for ChipKIT but does not affect Arduino #include <SoftwareSerial.h> // anndrews pins SoftwareSerial rs(4,7); //rx,tx // johns pins //SoftwareSerial rs(2,3); //rx,tx void setup() { pinMode(13, OUTPUT); digitalWrite(13, LOW); Serial.begin(115200); rs.
  7. I am posting a support question to help help drive the AnalogShield knowledge base on the forum. "I purchased 2 Analog Shields and 2 Chipkit UNO32 boards and am trying to use them together. The web page for the Analog Shield is misleading and implies that the Analog Shield is compatible with the the Chipkit Uno32. However I cannot get the Analog Shield library to compile in MPIDE. There is a compile error that sates something like "the library contains AVR specific code and will not work on the the UNO32" or something like that. What's the deal? How do I get the Analog Shield to wor