# Akshay Bhat

Members

9

• Rank
Newbie

## Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

Hi, Thanks for the reply in the attached thread , now i just need a help as the formula given for the voltage is correct in the same way is there any formula for the calculation of the temperature or can i use the same formula for the temperature also in my project I'm using this sensor for the temperature LMT84DCKT thanks and regards Akshay

Hello, I am also using the PMOD AD5 to get the values of two sensor one is voltage and another is temperature , but the problem is i wanted to get the value of the only voltage first then only temperature, what i did is i just added a function of the temperature to it with the same voltage code that is given in the example of the AD5 driver, i change the configuration register values to byte[1]=0x04 byte[2]=0x03 byte[3]=0x18 so that i can have the enable the 2 single channels and the value be in uni polar by doing this i am getting the values voltage is: 2.5v (which what i set in the POT) temperature is : 99.99 (which id taking the data of channel one and giving me the value) in next cycle voltage is taking the value from the channel 2 and giving me the value , here the temperature what i am getting is almost correct but i need it accurate . So can u please provide me with the code that will help me getting the values from the two different channel one after the other Thanks & Regards Akshay

Hello, I am also using the PMOD AD5 to get the values of two sensor one is voltage and another is temperature , but the problem is i wanted to get the value of the only voltage first then only temperature, what i did is i just added a function of the temperature to it with the same voltage code that is given in the example of the AD5 driver, i change the configuration register values to byte[1]=0x04 byte[2]=0x03 byte[3]=0x18 so that i can have the enable the 2 single channels and the value be in uni polar by doing this i am getting the values voltage is: 2.5v (which what i set in the POT) temperature is : 99.99 (which id taking the data of channel one and giving me the value) in next cycle voltage is taking the value from the channel 2 and giving me the value , here the temperature what i am getting is almost correct so when i tried to access to change the set slave value to 2 in the file Pmodad5.c i was not getting the values in the correct manner . So can u please provide me with the code that will help me getting the values from the two different channel one after the other Thanks & Regards Akshay
4. ## Pmod MTDS display on ZED board

Hello, The code which is in the will run on the Zynq custom board or do we need to add the board files to it ? Regards Akshay
5. ## Pmod MTDS display on ZED board

Thank you for the Reply Yes the project what u sent works I just wanted in the same way do to in my project so i asked u the steps how to do the in the SDK ? In Which i have to my own program to run on the FPGA, the error i am getting is in setup and loop are not defined in the main.c So if u can help me with this that will be really helpful for my project ... sorry for the trouble... With Regards Akshay
6. ## Pmod MTDS display on ZED board

Thanks for the Reply Actually i need how to generate the other SDK file after launching from vivado 2017.4 for my code? sorry for the trouble.. With Regards Akshay
7. ## Pmod MTDS display on ZED board

This answer was really helpful. I am new to SDK and I just tried to get the files as u did in the demo example but i am not able to extract the few files in the SDK, I think i am missing some steps, can u please send me the step to get all the files in these ''zedboard_demo" and .''zedboard_demo_bsp" ? With regards Akshay
8. ## Pmod MTDS display on ZED board

The reply was helpful and thanks for the reply I was using the ZED board i saw many pmod connection in that which pmod if preferred to MTDS in pmod_out and spi_out? If I get any demo project where the Pmod MTDS is working that will be really helpful to understand the flow and also if a user manual if available. Regards Akshay
9. ## Pmod MTDS display on ZED board

Hello , I am using the Pmod AD5 and Pmod MTDS on the Zedboard I am connecting the pmod AD5 with a simple POT and giving different values it. From the demo example in the mtds ip I got to know that display images are store in the file with .bmp in SD card then invoked when needed My problem is i have nearly 500 values in to be displayed so , my question Is there any way to dynamically generate the .bmp file to the MTDS and display it when we give the different values from the AD5 ? Regards Akshay