kursatgol

Members
  • Content Count

    16
  • Joined

  • Last visited

  • Days Won

    1

kursatgol last won the day on May 11 2015

kursatgol had the most liked content!

About kursatgol

  • Rank
    Member

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. Hi @paul2019, Yes i think it will run but i am not sure. Could you please give it a try and share with us please? regards. kursat
  2. Hi @malexander, Everything is fine from my side. I would share last point of my problem that the failure been regarding with xusb_xup.hex firmware file. The file which is coming with Vivado 2018.1 is not properly running but (I know hearing this is strange) the one which was coming with ISE-DS-14.6 is properly running on my host Windows 7. Thanks again for your kindly regards. kursat
  3. Hi @malexander, You are the one and you are the wonderful guy for me. Many thanks for your kindly answer. It works!!! I don't have any vivado installation on my host windows-7 so i don't want to install. When i connect the Xilinx XUP-USB debugger to Centos-7 vm and the solution was editing the /etc/udev/rules.d/52-xilinx-pcusb.rules file like below; [root@oeee lin]# cat /etc/udev/rules.d/52-xilinx-pcusb.rules SYSFS{idVendor}=="03fd", SYSFS{idProduct}=="0008", MODE="666" BUS=="usb", ACTION=="add", SYSFS{idVendor}=="03fd", SYSFS{idProduct}=="0007", RUN+="/sbin/fxload -v -t fx2 -I /usr/share/xusbdfwu.hex -D $TEMPNODE" BUS=="usb", ACTION=="add", SYSFS{idVendor}=="03fd", SYSFS{idProduct}=="0009", RUN+="/sbin/fxload -v -t fx2 -I /usr/share/xusb_xup.hex -D $TEMPNODE" BUS=="usb", ACTION=="add", SYSFS{idVendor}=="03fd", SYSFS{idProduct}=="000d", RUN+="/sbin/fxload -v -t fx2 -I /usr/share/xusb_emb.hex -D $TEMPNODE" BUS=="usb", ACTION=="add", SYSFS{idVendor}=="03fd", SYSFS{idProduct}=="000f", RUN+="/sbin/fxload -v -t fx2 -I /usr/share/xusb_xlp.hex -D $TEMPNODE" BUS=="usb", ACTION=="add", SYSFS{idVendor}=="03fd", SYSFS{idProduct}=="0013", RUN+="/sbin/fxload -v -t fx2 -I /usr/share/xusb_xp2.hex -D $TEMPNODE" BUS=="usb", ACTION=="add", SYSFS{idVendor}=="03fd", SYSFS{idProduct}=="0015", RUN+="/sbin/fxload -v -t fx2 -I /usr/share/xusb_xse.hex -D $TEMPNODE" ATTR{idVendor}=="03fd", ATTR{idProduct}=="0008", MODE="666" ATTR{idVendor}=="03fd", ATTR{idProduct}=="0007", MODE="666" ATTR{idVendor}=="03fd", ATTR{idProduct}=="0009", MODE="666" ATTR{idVendor}=="03fd", ATTR{idProduct}=="000d", MODE="666" ATTR{idVendor}=="03fd", ATTR{idProduct}=="000f", MODE="666" ATTR{idVendor}=="03fd", ATTR{idProduct}=="0013", MODE="666" ATTR{idVendor}=="03fd", ATTR{idProduct}=="0015", MODE="666" @malexander, My last question is in vivade hardware manager GUI i couldn't see the flash programming option with an *.mcs file? But impact has this feature? How can i program my zedboard's flash memory with Vivado 2018.1 hardware manager via Xilinx XUP-USB JTAG debugger/programmer? So now it's working. :) regards. kursat
  4. Hi @jpeyron and @JColvin, Is there any progress on this issue? If yes could you please share some screenshots and advices about installing method of drivers of Xilinx XUP JTAG debugger? regards. kursat
  5. Ok @jpeyron thank you and @JColvin for your kindly answer. Happy new year and have a good christmas. Regards. kursat
  6. Hi @JColvin, I tried with fedora 20 64 bit and ISE-DS 14.6 version. Everything was fine for zedboard and also additionally NetFPGA-1G-CML boards. I still think Digilent XUP debugger is not compliant for Vivado 2018.1. Could you please share any screenshots about installation drivers or running xup debugger? So i have for ISE-DS impact 14.6. regards. kursat
  7. Hi @dec, Did you fix this problem with @jpeyron's answer? If yes, could you please help me too? I met same problem like you and still i am struggling. I waste more time. regards. kursat
  8. Hi @JColvin, My exact question is that now i can connect via directly to FPGA without xup digilent jtag programmer on zedboard, centos vm, virtualbox and vivado 2018.1 But i couldn't connect with xup digilent jtag programmer on same parameters and conditions. I am suspecting vivado 2018.1 is not supporting Digilent Inc. XUP (Xilinx University Program) JTAG debugger-programmer? Am i right or wrong on my suspicious? regards kursat
  9. Hi @Edwardz, How can you solve your problem on this track? My problem is very similar with yours. Could you please help me urgently? regards kursat
  10. Hi @JColvin, My last status is this; My host PC OS: Win7 Virtualization Platform: Virtualbox 5.2.8 (Extension Pack 5.2.22 has installed for USB 2.0-3.0 support) Guest VM: Centos 7 - 64 bit VM USB settings: USB 3.0 enabled Xilinx Platform: Vivado 2018.1 JTAG Debugger: Digilent Xilinx University Program USB-JTAG debugger I can connect to FPGA without XUP via hardware manager but i can not connect with JTAG even connect to hw_server. i added the screenshots with xup debugger and without xup debugger. regards. kursat
  11. Hi @JColvin, You mentioned that on 28 June e-mail subject of "XUP USB-JTAG Programmer" on digilent forum "Our engineer was able to get the XUP cable recognized and working on a Centos 7 64-bit VM with Vivado 2018.1 without much issue." Could you please share more detail about the virtualization infrastructure for example VirtualBox or vmware? If vbox did this engineer install the virtualbox extension-pack for USB2.0 drivers recognizing? regards. kursat
  12. Hi @JColvin, Is there any update about XUP USB JTAG debugger as well on Linux systems? Did you ask about this issue to your design engineer? Regards kursatgol
  13. Hi @JColvin, How is your time progress? Will new XUP USB JTAG come to you in a short term or long term? Shall I wait your investigation? Thank you very much. kursatgol
  14. Thank you very much @JColvin for your kindly regards. I will be interst in your quote. Regards. kursat
  15. Hi All, Is there anybody have any experience about XUP (Xilinx University Program) USB-JTAG Programmer Revision-G using with Vivado 2015 or 2018? I have some little experience with Vivado 2015.5 and 2018.1 but regarding my experiences XUP USB-JTAG Programmer is not compatible with Vivado? I tried all ways on Centos-7 OS and the particular script (install_drivers.tar.gz). I aimed to program the Zedboard for petalinux applications developing but no success with XUP USB-JTAG Rev.G and Vivado running on Centos-7. Could you please share any suggestions if you have? Regards. Kursat Gol