-
Posts
5,826 -
Joined
-
Last visited
Reputation Activity
-
jpeyron got a reaction from dlgeng in How to restore FT2232 EEPROM back to factory settings?
Hi Robin,
I am tagging the engineer( @Bianca ) that has been handling most of the issues with the EEPROM to this thread.
cheers,
Jon
-
jpeyron reacted to thk3695 in JTAG-HS3, FT232 chip erased
Hi @jpeyron,
Thank You!
Best wishes,
Harshith
-
jpeyron got a reaction from thk3695 in JTAG-HS3, FT232 chip erased
Hi @thk3695,
I sent you a PM about this.
best regards,
Jon
-
jpeyron reacted to David_hale in Xilinx VCU-118 And Digilent USB-2-JTAG IC failure
Hi everyone,
The good folks here at Digilent sent my a PM containing instructions on how to re-flash the JTAG IC.
It worked and solved my issue.
Thanks again,
David.
-
jpeyron reacted to nob in JTAG-HS2 firmware erased by accident
jpeyron san
My HS1 is back and can be used again.
Thank you very much.
-
jpeyron reacted to mjdbishop in JTAG-HS2 firmware erased by accident
Hi Jon
Many thanks - cable now working
Many Thanks Martin
-
jpeyron got a reaction from Mohammad12gsj in How to restore FT2232 EEPROM back to factory settings?
Hi @Mohammad12gsj,
I have sent you a PM about this.
best regards,
Jon
-
jpeyron got a reaction from mzin92 in CMOD a7-35t Schematic
Hi @mzin92,
There is no difference in the schematic on page 4 or 7 between the Cmod A7 15T anf the Cmod A7 35T.
We do not publicly provide the BOM.
What information are you looking for specifically?
best regards,
Jon
-
jpeyron reacted to sm7ed in Vivado HLS Board Files for the ZyboZ7-20
BogdanVanca's solution worked for me as well. For the Pynq-Z1 board, I added the line:
<board name="Xilinx_PYNQ-Z1" display_name="Xilinx PYNQ-Z1" family="zynq" part="xc7z020clg400-1" device="xc7z020" package="clg400" speedgrade="-1" vendor="pynq.io" />
-
jpeyron got a reaction from Ahp in JTAG-USB Question
HI @Ahp,
You will need to contact "support dot digilent at ni dot com" to further discuss acquiring the license for the programming solution.
cheers,
Jon
-
-
jpeyron got a reaction from Iman in How to restore FT2232 EEPROM back to factory settings?
Hi @Iman,
I have sent you a PM about this.
cheers,
Jon
-
jpeyron reacted to albert.zzz in JTAG-HS2 firmware erased by accident
Hi @jpeyron
It worked!
Thank you for your kind support!
-
jpeyron got a reaction from JColvin in JTAG-HS2 firmware erased by accident
Hi @albert.zzz,
I have sent you a PM about this.
cheers,
Jon
-
jpeyron got a reaction from JColvin in DXF/CAD files for CORA Z7 board
Hi @Erickson,
The header is arduino/chipkit compatible as discussed in the Reference manual here in section 13 Arduino/chipKIT Shield Connector. The header has more available pins than the Arduino uno as shown here . The Arty A7 has the same header and we have a 3D CAD file available for the Arty-A7 on the bottom of the resource center here.
thank you,
Jon
-
jpeyron reacted to Erickson in DXF/CAD files for CORA Z7 board
Hi @jpeyron,
This is exactly what I needed. Thanks!
-
jpeyron got a reaction from JColvin in Incaution erase the EEPROM of JTAG-HS3 Programmer
Hi @roozeboos,
I have sent you a pm about this.
thank you,
Jon
-
-
jpeyron got a reaction from JColvin in JTAG-HS2 firmware erased by accident
Hi @GurAndrew,
Sorry about the late response. We missed your post. I have sent you a pm about this issue.
thank you,
Jon
-
-
-
jpeyron got a reaction from Marius in Nexys Video Artix-7 FPGA - Support for Analog Devices AD-FMCOMMS-EBZ
Hi Marius,
The Nexys Video's FMC is a fully loaded LPC. If the Zedboard's FMC works then the Nexys Video's will as well. You should contact Analog Devices to ensure that the difference between the Artix 7 and the Arm core doesn't affect the compatibility with the AD-FMCOMMS-EBZ.
thank you,
Jon
-
jpeyron reacted to StevenS in Welcome!
Hi, my name is Steve and I need the use of an MSO on occasion while working through Industrial Control problems for my customers. This devices shows promise, wish it was available when I was in College, would have made a great addition to our standard tool kit. I have used LabView as well as NI products over the years, for various projects including high speed shaft straighteners, Balancing equipment, vibration monitoring and mitigation on testing devices, etc... It was good to find a solution that fit for me in a specific price range, and provided a reasonable ADC bit level. The real bonus for me is the fact I can use it on my Linux box instead of having to rely on MS (unlike so many proprietary devices and software I deal with regularly). Kudos to Digilent for openness on their products.
-
jpeyron reacted to petersan in Welcome!
My name is Petersan and I am a newbie to the forum but not to the Digilent product line. I purchased the chipKIT Max32 and the network shield awhile ago and I’ve developed a few good projects, classes etc. (education only so far) that I used in the lab (the garage). My wife got me the chipKIT Wi-Fire and I can wait to cut my teeth on this new board and port my old projects over. I used to be reluctant at joining any of the forums; but now that I am a bit more involve on some more serious projects, I think there is great benefit to being part the group.