• Content Count

  • Joined

  • Last visited

About victagayun

  • Rank

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. Why it doesn't retry few times? In Arduino ESP8266 you would try to add few time of tries and timeout, why not do the same? This PC I am using is just 1m below the router. The shelf above where the router is, is just 1m above this PC and the Openscope. That means that the Openscope is about a meter from the router. I am using Linksys AC1900 (Max Stream EA7500) Dual Band Wireless Router 2.4Ghz and 5Ghz with only 5 devices connected. I don't need to do that. When I go to configuration menu, I just click the "saved network", it would connect right away. That means my credentials are all OK. It could be a problem in the field when using it without a USB connection to connect it to wifi. That means that I need to bring a laptop to configure it while on USB just to connect it to wifi. But when I unplug it expecting that it would connect to wifi, it would not. Then I would connect it again to a laptop to configure it to connect on wifi. Instead of just bringing a tablet, I would need to bring an extra laptop.
  2. Hello I also cannot reconnect to wifi at home even after few restart. Did all the suggestions above and even saved on both sdcard and flash. The only way is to always configure it every start then it would connect again to wifi. Here is the serial datalog: =~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2019.02.09 09:43:24 =~=~=~=~=~=~=~=~=~=~=~= ^@OpenScope v1.301.0 Written by: Keith Vogel, Digilent Inc. Copyright 2016 Digilent Inc. File Systems Initialized MRF24 Info -- DeviceType: 0x2 Rom Version: 0x31 Patch Version: 0xC USB+: 0uV VCC 3.3: 3313321uV VRef 3.0: 3001465uV VRef 1.5: 1500000uV USB-: -4824034uV SD card detected and mounted Using calibration from: flash Unable to connect to WiFi AP. Error 0xA000001B Enter the number of the operation you would like to do: 1. Enter JSON mode 2. Calibrate the instruments 3. Save the current calibration values 4. Manage your WiFi connections 5. View all files names on the SD card 6. View all files names in flash 7. Set the Oscilloscope input gain
  3. Got it! It is in usr/bin and can be run anywhere in the termiral by this "digilent-agent"
  4. After I double clicked the deb or by command line : [email protected]:~/Downloads$ sudo apt install ./digilent-agent_1.0.1-1_amd64.deb Reading package lists... Done Building dependency tree Reading state information... Done Note, selecting 'digilent-agent' instead of './digilent-agent_1.0.1-1_amd64.deb' digilent-agent is already the newest version (1.0.1-1). 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. [email protected]:~/Downloads$ sudo dpkg -i digilent-agent_1.0.1-1_amd64.deb (Reading database ... 208378 files and directories currently installed.) Preparing to unpack digilent-agent_1.0.1-1_amd64.deb ... Unpacking digilent-agent (1.0.1-1) over (1.0.1-1) ... Setting up digilent-agent (1.0.1-1) ... [email protected]:~/Downloads$ I cannot find the application.
  5. Hello, DO you have 3D print case of OpenScopeMZ with Discovery BNC combined?
  6. I always have this problem too. So we need to connect to PC by USB then we can use any mobile device. Once it is connected and we want to use in the field, it then does not reconnect. Only after you connect it by USB to wifi. In this case, how to use in the field using mobile device????
  7. victagayun


    Those of you who want to expand your instruments... might be interested in Omniboard...
  8. Hopefully, will be able to implement very soon, I "+1" it already...
  9. I have this parts kit, except that it does not have the vibration sensor.
  10. Seems to be similar to
  11. Seems to be working now.... Not sure what version of WaveformsLive it is...
  12. Will there be an upgrade like this in the near future? waiting.....
  13. You may try to use the labs used for Analog Devices ADALM1000