mustafasei

Members
  • Content count

    15
  • Joined

  • Last visited

  • Days Won

    1
  1. Blinking LED always ON for RPI3

    Hi Th e LED start to be continuous ON ( NOT Blinking ) before loading the VI and once the installation of labview complete on the RPI3
  2. Blinking LED always ON for RPI3

    Please see instructions which I follow in below : https://www.labviewmakerhub.com/doku.ph ... y-pi-setup for the link above at 5:35 of the video the external LED which connected on pin no.7 start to be ON all the time. I changed the GPIO from 7 to 8 and I got error message that GPIO in (((RPI2))) not supported and same if I select other GPIOs also why I see in the project (((RPI2 and NOT RPI3))) see attached
  3. Blinking LED always ON for RPI3

    Hi Pin no.7 But the problem this pin start to give supply to external Led once the installation of labview on the RPI3 done even before opening the VI to send it to the RPI3
  4. Blinking LED always ON for RPI3

    Any answer ???!!!!!!
  5. Blinking LED always ON for RPI3

    Hi I have RPI3 and I did the setup in makerhub videos but after installing the labview on the RPI3 as shown in picture the LED starts to be ON all the time even after running the VI on the RPI3 please advise if there is any idea for this issue
  6. need advice

    Hi Austin Is it possible to use your instructions above as a standard form for any kind of codes ? i have some codes in this page http://www.locobots.com/node/24 and I want to use one of them ( Knob control and DVD tray stepper:) as custom command , is it same procedure or there will be some differences
  7. need advice

    Thank you very much for your support. it is work now and every thing is OK
  8. need advice

    Arduino Uno
  9. need advice

    When I use the arduino code for the DHT11 it works good but when i use the Labview VI in examples not work and give me the error above any idea
  10. need advice

    When I use the arduino code for the DHT11 it works good but when i use the Labview VI in examples not work and give me the error above
  11. need advice

    I tried all above and nothing new just the same error message which I attached before.
  12. need advice

    Any advice please
  13. need advice

    Hi Thank you for your replay, I'm still struggle for building a custom command due to my very poor experience in C++. I have seen the makerhub which you send to me many times but I have no idea how to copy and paste my codes of arduino sensors which i have in my 37 sensor kit so let us say in this way : if i have the below code for the DHT11: ( #include <dht.h> #define dht_apin A0 // Analog Pin sensor is connected to dht DHT; void setup(){ Serial.begin(9600); delay(500);//Delay to let system boot Serial.println("DHT11 Humidity & temperature Sensor\n\n"); delay(1000);//Wait before accessing Sensor }//end "setup()" void loop(){ //Start of Program DHT.read11(dht_apin); Serial.print("Current humidity = "); Serial.print(DHT.humidity); Serial.print("% "); Serial.print("temperature = "); Serial.print(DHT.temperature); Serial.println("C "); delay(5000);//Wait 5 seconds before accessing sensor again. //Fastest should be once every two seconds. }// end loop() ) where shall i past the above code on what has explained in makerhub website for how to create the custom command thanx
  14. need advice

    Hi Thank you for your replay, I'm still struggle for building a custom command due to my very poor experience in C++. I have seen the makerhub which you send to me many times but I have no idea how to copy and paste my codes of arduino sensors which i have in my 37 sensor kit so let us say in this way : if i have the below code for the DHT11: ( #include <dht.h> #define dht_apin A0 // Analog Pin sensor is connected to dht DHT; void setup(){ Serial.begin(9600); delay(500);//Delay to let system boot Serial.println("DHT11 Humidity & temperature Sensor\n\n"); delay(1000);//Wait before accessing Sensor }//end "setup()" void loop(){ //Start of Program DHT.read11(dht_apin); Serial.print("Current humidity = "); Serial.print(DHT.humidity); Serial.print("% "); Serial.print("temperature = "); Serial.print(DHT.temperature); Serial.println("C "); delay(5000);//Wait 5 seconds before accessing sensor again. //Fastest should be once every two seconds. }// end loop() ) where shall i past the above code on what has explained in makerhub website for how to create the custom command thanx
  15. need advice

    Hi I'm new user for Labview and arduino and recently start to use the arduino with labview via Linx firmware and labview 2013 and doing some small projects or experiments but i have some difficulties with some sensors of arduino which i have it now the 37 kit like the 18B20 and DHT11 and so. I have no idea about the arduino programming language C++ which is I'm totally far away from it. i need your support for how to define some of the arduino sensors to be known in labview menu like (makerhub-linx-sensors-temp-tmp3x) i have searched in makerhub forums and got answer that i have to use the custom command which is something i cannot use due to my poor ability in C++. please advise