• Content Count

  • Joined

  • Last visited

About JohnBee

  • Rank

Profile Information

  • Gender
  • Location
    Newfoundland Canada
  • Interests
    Education, Electronics, Music, Art, Science

Recent Profile Visitors

1880 profile views
  1. And if so, will it work on USB 3.1?
  2. We've been deliberating what projects to implement in our homeschool classes to make good use of the our Discovery 2 kit. And I began to wonder if there were any walk-through type exercises that our children could follow and learn on electrical circuits using diligent products? PS. our children range from ages 7 - 17
  3. Okay thanks for that, I think I have a better understanding now. That said, what would be the proper way to position the resistor in my circuit? Would I place the resistor in series on the positive side of the circuit, or across both sides(+ and -)? With that being said, and just to be sure I'm understanding, connecting C1 to ground would be the wrong approach to take in this particular case?
  4. Just to be sure I'm understanding this correctly, is this approach based on using two channels? That is to say, one channel measuring each side of the resistor? And then using a math-channel to calculate the difference i.e. the voltage drop across the resistor?
  5. Hi attila, I too would like to know how to do this, and so I wanted to ask if you could provide screenshots on how to do this? Sincerely, JohnB
  6. Actually I was trying to use the 1 and 2 + /- off the BNC module. which was messing-up my readings. - Lesson learned. PS. it might be helpful to add a note in the BNC module to highlight the pin-out changes. Not sure if it's indicated in the overview etc. but I missed this, and it cost me alot of time and effort in trying to get things setup properly.
  7. NC = No Connectivity? As it turns out, this was my issue all along. As I was trying to use the leads(ether Waveform Gen(1,2) and the Oscilloscope(P,N) to calibrate with. To which I'd add, I did not see the pin-out assignment changes in the BNC documentation :/ That said, I'm happy to report that the unit is now calibrated and the waves and behavior looks much better than it did before. Too bad it took this long to figure out the problem though.
  8. Okay so I had another go at it and found the same error; Check the connections!! The measured voltage on Oscilloscope Channel 1 is between: 2.244575 V and 2.245164 V But it should be around: 5 V It might be that the Arbitrary Waveform Generator 1 Offset is not calibrated correctly. That said, are the break-out leads on the BNC modules working in the same way as they would be directly from the unit?
  9. Awesome info yet again! I'll give it a try just as soon as I get in today. - Fingers crossed
  10. Thanks for the response. As it turns out, I discovered that my BNC adapter was the culprit. I removed it and everything came to life (as intended). Though I'm still not sure what is causing the anomalies at the moment. Though the moment I remove the module, everything displays as it should(voltage, waveforms etc). And so I guess this is good news in that I don't have to send in my unit for repair.
  11. Success, I was able to calibrate the unit without the BNC module attached to it. Though when I attach it, I cannot calibrate it(error). Does this mean the module is defective or is this a normal consequence to having the module attached?
  12. Hi JColvin, I'm currently using v3.3.5. Though I think I may have made headway in that it appears as though my issues may be due in-part with the BNC adapter module. And so I'm going to run a few more tests this evening in hopes of pin-pointing the issue.
  13. It appears as though my unit cannot be calibrated (error) on voltage. I tried calibrating it several times to try and get it to display wave-forms properly, but the calibration fails on the second portion of the scope as a result of the offset being to far out of spec. Given the rash or issues I've been having with this unit since we received it, I'm beginning to think it's malfunctioning and should be returned for further inspection. Needless to say, I can't help but feel as though we've gone in the wrong direction with this purchasing instead of getting a physical scope. :/
  14. PS. the output source for the tests was confirmed using a conventional DMM
  15. Another update, and in an attempt to identify the issue(user or otherwise) I downgraded the software increimentally down to 3.1.5 and found that the Logger does show activity on the Meter side with DC, though the readings appear significantly skewed. That said, and with this in mind, is it possible that my device is not working properly? I've had my doubts about the unit since it arrived as it appears to have been erratic in function. Sometimes working, sometimes not without changing settings etc. Which leads me to ask if there's a diagnostic tool I could run on the Discovery 2 i