Mingfei

Members
  • Content Count

    7
  • Joined

  • Last visited

About Mingfei

  • Rank
    Newbie

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. Hi Jon, Thank you so much for helping me out! Forgive me for late reply. I was working on my final report recently. Just one more question, in "main" function in demo code. I noticed that there is a sleep(10); function which can set 10 seconds delay before generating the next output. By changing this delay, the output data rate from SDK console can also be changed. So can I ask that if the data rate we set in "mode register" is the maximum data rate that can be achieved? Mingfei
  2. Hi everyone, I'm building a project based on arty-z7 hdmi demo to display a series continuous moving images. Basically, I made some changes to DemoInverterFrame() function and use it to load in my image. Then, I put this in a while(1) loop to make it continuous changing frames. I have attached a part of the code as attachment. Everything works fine, the only problem is that HDMI display can only refresh 8 new images per second. Can I ask that if there is any way to increase this to 50fps? Thank you! Mingfei
  3. Hi everyone, I'm using Pmod AD5 on PYNQ Z1 board. I used the demo code and it works fine. I'm wondering if I can change the data rate of Pmod AD5? By default it is about 6 samples per second and I want to change it to about 50. I checked the AD7193 datasheet and it says the last 10 bits of mode registers control the data rate (FS[0] to FS[9]). I found a function in demo code called "AD5_WriteConfig(PmodAD5* InstancePtr)" . Can I ask that should I change values in Bytes[3] to change data rate? Since I tried some numbers in Bytes[3], it doesn't work. Function: Datasheet: Thank you for your help Mingfei
  4. Hi Joe, Thank you so much for you help! It works! So I can now continue my final project. Mingfei
  5. Hi Jon, It seems that Pmod AD5 IP cores can not work with IP cores in the HDMI out. I looked at other people who have similar critical warnings and they suggest to delete the original wrapper and generate a new one. I tried that and got rid of the critical warnings. However, an error occurred when generating bitstream. The errors are shown below: So I referred to HDMI-OUT demo's implementation design and assigned these three pins manually. Then I got another error saying about conflicting voltage: I'm wondering that does this mean these two IPs cannot be used together? Thank you for helping me!
  6. Hi Jon, Thanks for answering my question. I followed your instruction step by step, but I still get the same result. In SDK, I used the demo code. When running the program, I still get a constant value for the voltage in SDK console. However, if I start a new project and only use Pmod AD5 and ZYNQ processor, Pmod AD5 works fine and I can get a small changing voltage ( due to noise I think). I have attached the result for both. I'm confused that, in SDK, will the demo code work if ZYNQ processor is not only connected to Pmod AD5? Or do I have to make some changes to the code to make it work? Because the demo code works fine if I don't use the HDMI demo. Thank you so much
  7. Hi everyone, I'm really new to digilent board. I'm using the PYNQ-Z1 board to do my final project. What I'm gonna build is basically an oscilloscope. I use Pmod-AD5 to measure voltage, then use HDMI OUT port on PYNQ-Z1 to display the voltage value. Because the PYNQ board has the same board files as ARTY-Z7, so my project is based on Arty Z7 HDMI Out Demo:https://reference.digilentinc.com/learn/programmable-logic/tutorials/pmod-ips/start . The HDMI demo works fine. Then I followed this link: https://reference.digilentinc.com/learn/programmable-logic/tutorials/pmod-ips/start to use Pmod. I first test the Pmod-AD5 by creating a new project with one ZYNQ processor connected to Pmod AD5 and it works fine. However, If I added Pmod to HDMI demo, I can only get a constant voltage value from AD5 and it doesn't change no matter what voltage I input. I have attached the critical warning as attachment. It seems like a problem with constraints. So may I ask whether if I should add Pmod constraints and how to do that? I also attached the block diagrams of HDMI demo, my test for Pmod, and the HDMI demo with Pmod. Thank you so much for helping me.