U-Boot 2017.01-03096-g559c218 (Jan 24 2017 - 15:41:16 +0530) Model: Zynq Zed Development Board Board: Xilinx Zynq DRAM: ECC disabled 512 MiB MMC: sdhci@e0100000: 0 SF: Detected s25fl256s_64k with page size 256 Bytes, erase size 64 KiB, total 32 MiB In: serial@e0001000 Out: serial@e0001000 Err: serial@e0001000 Model: Zynq Zed Development Board Board: Xilinx Zynq Net: ZYNQ GEM: e000b000, phyaddr 0, interface rgmii-id eth0: ethernet@e000b000 Hit any key to stop autoboot: 0 Unknown command 'sdboot' - try 'help' Zynq> Zynq> run sdboot Copying Linux from SD to RAM... Device: sdhci@e0100000 Manufacturer ID: 3 OEM: 5344 Name: SS08G Tran Speed: 50000000 Rd Block Len: 512 SD version 3.0 High Capacity: Yes Capacity: 7.4 GiB Bus Width: 4-bit Erase Group Size: 512 Bytes reading uImage 4100368 bytes read in 362 ms (10.8 MiB/s) reading devicetree.dtb 10186 bytes read in 18 ms (551.8 KiB/s) reading uramdisk.image.gz ** Unable to read file uramdisk.image.gz ** ## Booting kernel from Legacy Image at 03000000 ... Image Name: Linux-4.9.0-ga25bc6b-dirty Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4100304 Bytes = 3.9 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Flattened Device Tree blob at 02a00000 Booting using the fdt blob at 0x2a00000 Loading Kernel Image ... OK Loading Device Tree to 1eb1f000, end 1eb247c9 ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. Booting Linux on physical CPU 0x0 Linux version 4.9.0-ga25bc6b-dirty (user@user-HP-ProBook-4420s) (gcc version 6.2.1 20161114 (Linaro GCC Snapshot 6.2-2016.11) ) #1 SMP PREEMPT Fri Mar 9 15:26:15 IST 2018 CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache OF: fdt:Machine model: Zynq Zed Development Board bootconsole [earlycon0] enabled INITRD: 0x00800000+0x01000000 overlaps in-use memory region - disabling initrd cma: Reserved 128 MiB at 0x16800000 Memory policy: Data cache writealloc percpu: Embedded 13 pages/cpu @dfb94000 s23564 r8192 d21492 u53248 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 Kernel command line: console=ttyPS0,115200n8 root=/dev/ram rw initrd=0x00800000,16M earlyprintk mtdparts=physmap-flash.0:512K(nor-fsbl),512K(nor-u-boot),5M(nor-linux),9M(nor-user),1M(nor-scratch),-(nor-rootfs) PID hash table entries: 2048 (order: 1, 8192 bytes) Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 379648K/524288K available (5590K kernel code, 240K rwdata, 2204K rodata, 256K init, 154K bss, 13568K reserved, 131072K cma-reserved, 0K highmem) Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xffc00000 - 0xfff00000 (3072 kB) vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) modules : 0xbf000000 - 0xbfe00000 ( 14 MB) .text : 0xc0008000 - 0xc057dc34 (5592 kB) .init : 0xc07ce000 - 0xc080e000 ( 256 kB) .data : 0xc080e000 - 0xc084a0c0 ( 241 kB) .bss : 0xc084a0c0 - 0xc0870974 ( 155 kB) Preemptible hierarchical RCU implementation. Build-time adjustment of leaf fanout to 32. RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2 NR_IRQS:16 nr_irqs:16 16 efuse mapped to e0800000 slcr mapped to e0802000 L2C: platform modifies aux control register: 0x72360000 -> 0x72760000 L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000 L2C-310 erratum 769419 enabled L2C-310 enabling early BRESP for Cortex-A9 L2C-310 full line of zeros enabled for Cortex-A9 L2C-310 ID prefetch enabled, offset 1 lines L2C-310 dynamic clock gating enabled, standby mode enabled L2C-310 cache controller enabled, 8 ways, 512 kB L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001 zynq_clock_init: clkc starts at e0802100 Zynq clock init sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns Switching to timer-based delay loop, resolution 3ns clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns timer #0 at e080a000, irq=17 Console: colour dummy device 80x30 Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) CPU: Testing write buffer coherency: ok CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 Setting up static identity map for 0x82c0 - 0x8318 CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 Brought up 2 CPUs SMP: Total of 2 processors activated (1333.33 BogoMIPS). CPU: All CPU(s) started in SVC mode. devtmpfs: initialized VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns pinctrl core: initialized pinctrl subsystem NET: Registered protocol family 16 DMA: preallocated 256 KiB pool for atomic coherent allocations cpuidle: using governor ladder hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. hw-breakpoint: maximum watchpoint size is 4 bytes. zynq-ocm f800c000.ocmc: ZYNQ OCM pool: 256 KiB @ 0xe0840000 zynq-pinctrl 700.pinctrl: zynq pinctrl initialized SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb media: Linux media interface: v0.10 Linux video capture interface: v2.00 pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti PTP clock support registered EDAC MC: Ver: 3.0.0 Advanced Linux Sound Architecture Driver Initialized. clocksource: Switched to clocksource arm_global_timer NET: Registered protocol family 2 TCP established hash table entries: 4096 (order: 2, 16384 bytes) TCP bind hash table entries: 4096 (order: 3, 32768 bytes) TCP: Hash tables configured (established 4096 bind 4096) UDP hash table entries: 256 (order: 1, 8192 bytes) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) NET: Registered protocol family 1 hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available futex hash table entries: 512 (order: 3, 32768 bytes) workingset: timestamp_bits=30 max_order=17 bucket_order=0 io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) dma-pl330 f8003000.dmac: Loaded driver for PL330 DMAC-241330 dma-pl330 f8003000.dmac: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16 e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 26, base_baud = 3125000) is a xuartps ąconsole [ttyPS0] enabled console [ttyPS0] enabled bootconsole [earlycon0] disabled bootconsole [earlycon0] disabled xdevcfg f8007000.devcfg: ioremap 0xf8007000 to e081c000 [drm] Initialized brd: module loaded loop: module loaded m25p80 spi0.0: found s25fl256s1, expected n25q128a11 m25p80 spi0.0: s25fl256s1 (32768 Kbytes) 5 ofpart partitions found on MTD device spi0.0 Creating 5 MTD partitions on "spi0.0": 0x000000000000-0x000000100000 : "qspi-fsbl-uboot" 0x000000100000-0x000000600000 : "qspi-linux" 0x000000600000-0x000000620000 : "qspi-device-tree" 0x000000620000-0x000000c00000 : "qspi-rootfs" 0x000000c00000-0x000001000000 : "qspi-bitstream" MACsec IEEE 802.1AE libphy: Fixed MDIO Bus: probed libphy: mdio_driver_register: xgmiitorgmii tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky libphy: MACB_mii_bus: probed macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 28 (00:0a:35:00:01:22) Marvell 88E1510 e000b000.etherne:00: attached PHY driver [Marvell 88E1510] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1) ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver usbcore: registered new interface driver usb-storage usbcore: registered new interface driver usbserial usbcore: registered new interface driver usbserial_generic usbserial: USB Serial support registered for generic usbcore: registered new interface driver ftdi_sio usbserial: USB Serial support registered for FTDI USB Serial Device usbcore: registered new interface driver pl2303 usbserial: USB Serial support registered for pl2303 e0002000.usb supply vbus not found, using dummy regulator ULPI transceiver vendor/product ID 0x0451/0x1507 Found TI TUSB1210 ULPI transceiver. ULPI integrity check: passed. ci_hdrc ci_hdrc.0: EHCI Host Controller ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1 ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected mousedev: PS/2 mouse device common for all mice i2c /dev entries driver cdns-i2c e0004000.i2c: 100 kHz mmio e0004000 irq 23 usbcore: registered new interface driver uvcvideo USB Video Class driver (1.1.1) gspca_main: v2.14.0 registered cdns-wdt f8005000.watchdog: Xilinx Watchdog Timer at e08f8000 with timeout 10s Xilinx Zynq CpuIdle Driver started sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman sdhci-pltfm: SDHCI platform and OF driver helper mmc0: SDHCI controller on e0100000.sdhci [e0100000.sdhci] using DMA ledtrig-cpu: registered to indicate activity on CPUs hidraw: raw HID events driver (C) Jiri Kosina usbcore: registered new interface driver usbhid usbhid: USB HID core driver NET: Registered protocol family 17 Registering SWP/SWPB emulation handler hctosys: unable to open rtc device (rtc0) mmc0: new high speed SDHC card at address aaaa ALSA device list: No soundcards found. mmcblk0: mmc0:aaaa SS08G 7.40 GiB mmcblk0: p1 p2 List of all partitions: 0100 16384 ram0 (driver?) 0101 16384 ram1 (driver?) 0102 16384 ram2 (driver?) 0103 16384 ram3 (driver?) 0104 16384 ram4 (driver?) 0105 16384 ram5 (driver?) 0106 16384 ram6 (driver?) 0107 16384 ram7 (driver?) 0108 16384 ram8 (driver?) 0109 16384 ram9 (driver?) 010a 16384 ram10 (driver?) 010b 16384 ram11 (driver?) 010c 16384 ram12 (driver?) 010d 16384 ram13 (driver?) 010e 16384 ram14 (driver?) 010f 16384 ram15 (driver?) 1f00 1024 mtdblock0 (driver?) 1f01 5120 mtdblock1 (driver?) 1f02 128 mtdblock2 (driver?) 1f03 6016 mtdblock3 (driver?) 1f04 4096 mtdblock4 (driver?) b300 7761920 mmcblk0 driver: mmcblk b301 1048576 mmcblk0p1 000505d9-01 b302 6712320 mmcblk0p2 000505d9-02 No filesystem could mount root, tried: ext3 ext2 ext4 vfat msdos Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(1,0) CPU: 1 PID: 1 Comm: swapper/0 Not tainted 4.9.0-ga25bc6b-dirty #1 Hardware name: Xilinx Zynq Platform [] (unwind_backtrace) from [] (show_stack+0x10/0x14) [] (show_stack) from [] (dump_stack+0x88/0x9c) [] (dump_stack) from [] (panic+0xdc/0x248) [] (panic) from [] (mount_block_root+0x288/0x2c8) [] (mount_block_root) from [] (prepare_namespace+0x17c/0x1c0) [] (prepare_namespace) from [] (kernel_init_freeable+0x1d4/0x1e4) [] (kernel_init_freeable) from [] (kernel_init+0xc/0xf0) [] (kernel_init) from [] (ret_from_fork+0x14/0x3c) CPU0: stopping CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.9.0-ga25bc6b-dirty #1 Hardware name: Xilinx Zynq Platform [] (unwind_backtrace) from [] (show_stack+0x10/0x14) [] (show_stack) from [] (dump_stack+0x88/0x9c) [] (dump_stack) from [] (ipi_cpu_stop+0x64/0x74) [] (ipi_cpu_stop) from [] (handle_IPI+0x6c/0x7c) [] (handle_IPI) from [] (gic_handle_irq+0x88/0x8c) [] (gic_handle_irq) from [] (__irq_svc+0x6c/0xa8) Exception stack(0xc080ff30 to 0xc080ff78) ff20: 00000000 00000000 1f38c000 dfb99100 ff40: 47ee12a2 00000000 dfb98490 00000001 486302fa 00000000 00000000 c0811084 ff60: 00600000 c080ff80 c03cff80 c03cff84 00000113 ffffffff [] (__irq_svc) from [] (cpuidle_enter_state+0x17c/0x2a0) [] (cpuidle_enter_state) from [] (cpu_startup_entry+0x138/0x204) [] (cpu_startup_entry) from [] (start_kernel+0x388/0x394) [] (start_kernel) from [<0000807c>] (0x807c) ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(1,0)